So as I moved it to the second port, WA-LA, it saw it. Report migetsub- Apr 29, 2010 02:24AM i have this problem too I also have no clue what to do to fix it Reply Report ricky- Aug 25, 2010 03:17PM i am But this new motherboard won't detect the hard drive. When I tried to on my laptop, I heard some strange noise coming from the hard drive and then "operating system not found" was displayed on the screen..my question is do
Computer Doesn't Recognize External Hard Drive
But, entry is usually provided by pressing the DEL key, the F2 key, the F11 key or the F12 key during POST. 0Votes Share Flag Back to Hardware Forum 9 total What's going on, and how can I resolve it? Any help guys? If it's on the same channel as the Hitachi drive with XP on it, the BIOS recognizes the other drive, but fails to boot from it.
Report • #7 GlobalGK January 11, 2010 at 14:22:49 I thought it was windows error with the HD. What are you trying to do with it? current community blog chat Super User Meta Super User your communities Sign up or log in to customize your list. Computer Won't Recognize Hard Drive To Boot the device at the end of the cable is master, the one in the middle slave or both at CS (cable select) if they are SATA there shouldn't be any problems
Have you experienced any kind of recent power outages/surges around the time it stopped working even for a second? Computer Doesn't Recognize Hard Drive In Bios Flag Permalink This was helpful (0) Collapse - Good to hear it's resolved ...Thanks for the feedback by VAPCMD / January 30, 2010 12:58 AM PST In reply to: Resolved... Such opinions may not be accurate and they are to be used at your own risk. There might be an option to enable a "boot delay", or "IDE detect delay" or something like that.
Please remember to be considerate of other members. Computer Can't Find Hard Drive Boot Welcome to OCF! The GRAY one in the middle goes to the HDD you set as Slave.4. If your drive is not detected it may be because it is turned OFF in System Setup.
Computer Doesn't Recognize Hard Drive In Bios
All with the same effect. When you connected it to your laptop computer did you make any jumper changes on the back of the drive?Did you have the other computer unplugged while doing all the swapping?In Computer Doesn't Recognize External Hard Drive But, that's a horse of a different color.Try getting one device at a time to work. Computer Doesn't Detect Hard Drive by DarkLink117 / January 30, 2010 12:43 AM PST In reply to: PC not detecting slave IDE Hello everyone, thanks for trying to help me, I have been busy.
All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. useful reference The CD set to slave. ONE HDD MUST be set to be Master using the jumper on the back edge and the diagram. Computing.Net and Purch hereby disclaim all responsibility and liability for the content of Computing.Net and its accuracy. Computer Can't Detect Hard Drive
The other one with XP came from the same computer, and I can boot from it, if that drive is in by itself. Now my other two IDE drives when connected are not showing partitions in windows also it is asking me to format the drive, which I am afraid as it might erase The drive is at the end of the cable and jumpered for master. my review here If you have 3 IDE devices, you must have 2 data cables and two controlers to plug into on the motherboard.
Other times, I'll go entire days of restarting before it works again. Bios Wont Detect Hard Drive What should the jumper settings be? Each device must be jumpered according to which cable it's on.
Does it even matter?
Maybe your cables have gone bad. Forcing everyone to speak the same language Why is looping over find's output bad practice? Which OS do you want to run? Internal Hard Disk Not Detected Do you have the IDE drive plugged into the primary device controller or the secondary?
Is it possible for a diesel engine computer to detect (and prevent) a runaway condition? Report • #3 OtheHill January 11, 2010 at 12:09:05 So you were in the BIOS options. Check the boot device config, or if the board uses the jmicron controller, IDE detection takes place after POST - at least on ASUS boards. How can I tell if the drive is damaged?
Desktop 4-5 rears old. Also, make sure that all of the cables are firmly reconnected to the hardware. I booted up into my normal windows( this is where I am as i type). I'll see I I can flash bios with download from Gateway website.
So my jumpers need to be set for master right? Register now Not a member yet? As soon as windows starts to load, plug in that molex to power on the IDE drive. If you can use the second drive as a boot drive, install XP on that one fresh Jan 2, 2012 #6 (You must log in or sign up to reply
I would use the second port on the IDE cable. SkyHawk Surveillance: Smart, Safe, Secure: SkyHawk Surveillance Hard Drives. Nothing can be detected in Windows if the BIOS don't see it first.Did you bend a pin in the plugs or plug a cable in backwards? ferdinan Sitohang July 9, 2012 at 4:42 am If you have another good PATA drive, change the current drive into the new PATA drive.
But, it's all you can do given the HDD drive that you have to use.No matter what you do, it takes a 2nd data cable for the 2nd controler, if you only one device connect to ide cable(DVD rom). These are not showing up in Windows or the bios. US Election results 2016: What went wrong with prediction models?
Computing.Net cannot verify the validity of the statements made on this site. how to reset BIOS if I can only go into setup.